Hardened & Tempered Jaws. Shiny Ground Finish

• Capacity: 0-#8

Manufacturer: VME

High Speed Steel. Ground Thread . Plug taps are the most popular hand tap, with a lead in between Taper Taps and Bottoming Taps. Can be used in a machine as well as by hand( but it does not drive the chips ahead like a Spiral Point Tap).

• Size: 0-80
• High Speed Steel. Ground Thread

Manufacturer: VME

High Speed Steel. Round Adjustable Die.

• Size: #0
• Threads Per Inch: 80
• Outside Diameter: 13/16"
• Cuts external threads.
• Die is held in a die stock or die holder (not included).

Manufacturer: VME

- 19/32 x 1-7/8" - No. 0 - Made of compressed hardwood - Small - Bag/50

• 19/32 x 1-7/8"
• No. 0
• Made of compressed hardwood
• Small
• Bag/50

Manufacturer: Wolfcraft

For handling miniature and micro-miniature parts. With tapered shanks, not as thick as pattern No. OO, flat edges and points that have ben honed and are very sharp. Overall length 4-1/2" (114 mm).

Manufacturer: Euro Tool

Regular Length. 60 Degree included angle on body. High Speed Steel. Double end

• Size: #0
• Body: 1/8"
• Drill: 1/32"
• Used to drill 60 degree centering holes.

Manufacturer: VME

For chucks with Jacobs taper backs. Determine both shank size (to fit into your Drill Press,tailstock, etc.) & chuck (Jacobs) taper to order the correct arbor. Morse Taper arbors have a tang end (Not available with a drawbar end.).

• Shank Size: 0 Morse Taper
• Chuck (Jacobs) Taper: 2JT
• Note: Photo shows a Morse Taper to Jacobs Taper arbor, but not necessarily this specific arbor.
• Please do not use the photo to judge the relative size of the tapers.

Manufacturer: Drill Chuck Arbors

For chucks with Jacobs taper backs. Determine both shank size (to fit into your Drill Press,tailstock, etc.) & chuck (Jacobs) taper to order the correct arbor. Morse Taper arbors have a tang end (Not available with a drawbar end.).

• Shank Size: 0 Morse Taper
• Chuck (Jacobs) Taper: 3JT
• Note: Photo shows a Morse Taper to Jacobs Taper arbor, but not necessarily this specific arbor.
• Please do not use the photo to judge the relative size of the tapers.

Manufacturer: Drill Chuck Arbors

For chucks with Jacobs taper backs. Determine both shank size (to fit into your Drill Press,tailstock, etc.) & chuck (Jacobs) taper to order the correct arbor. Morse Taper arbors have a tang end (Not available with a drawbar end.).

• Shank Size: 0 Morse Taper
• Chuck (Jacobs) Taper: 33JT
• Note: Photo shows a Morse Taper to Jacobs Taper arbor, but not necessarily this specific arbor.
• Please do not use the photo to judge the relative size of the tapers.

Manufacturer: Drill Chuck Arbors

For chucks with Jacobs taper backs. Determine both shank size (to fit into your Drill Press,tailstock, etc.) & chuck (Jacobs) taper to order the correct arbor. Morse Taper arbors have a tang end (Not available with a drawbar end.).

• Shank Size: 0 Morse Taper
• Chuck (Jacobs) Taper: 6JT
• Note: Photo shows a Morse Taper to Jacobs Taper arbor, but not necessarily this specific arbor.
• Please do not use the photo to judge the relative size of the tapers.

Manufacturer: Drill Chuck Arbors